Floors » Building Regulations South Africa
Nov 152011
 

Building Regulations that Apply to Floors

Floor 700 Floors

Floors can look beautiful, but what lies beneath has to have been constructed and built to the South African National Standards. You really do not want your beautifully newly laid floor cracking up because the foundations are cracking, or the tiles lifting because of rising damp.

The Application of the National Building Regulations that apply to floors (Part J of SANS 10400) are certainly not exhaustive. In fact, if you think of how much of our house is floor, it’s what we might, in South Africa, describe as a biekie min. But the authorities have, at least, increased this part of the document from a single page to nine pages (although these include a page of references to other SANS that need to be taken into account, and more than a page of definitions) plus a cover page, a Foreword, Contents page, an Annex that gives the official, legal Regulations (see below), a one-line Bibliography – on a full page, a couple of blank pages and some info about the SABS Standards Division.

Changes to the Law

Like all the other parts of SANS 10400, Part J, Floors, has two sections. One section covers the Regulations (the National Building Regulations and Building Standards Act, 1977 and all its amendments) and the other covers how they should be applied (previously what fell under the “deemed-to-satisfy” rules).

In terms of the Regulations (the law), there is one substantial change to the first general requirement that previously stated that any floor of a building must simply “be strong enough to safely supports its own weight and any loads to which it is likely to be subjected”. It now states that “any floor of any building shall be designed and constructed to safely support its owns weight and any actions which can reasonably be expected to occur and in such a manner that any local damage (including cracking), deformation or vibration do not compromise the efficient use of the building or the functioning of equipment supported by such a floor”.

In addition (and this hasn’t changed):

  • Floors must be fire resistant and where necessary, non-combustible.
  • Floors of laundries, kitchens, shower-rooms, bathrooms and toilets (hooray, they are no longer referred to as WCs!) and urinals must be water resistant.
  • Timber floors must have adequate under-floor ventilation.
  • Concrete floors supported on ground or filling must be constructed in such a way that moisture will not penetrate the floor slab.

As always, the Regulations state that these requirements will be “deemed to be satisfied” if the design and construction of the floor complies with this part of SANS 10400. However, if the local authority deems it necessary, certain other requirements may be needed. For instance the local authority may demand that the entire area within the foundation walls of any building be covered by a suitable damp-proof membrane, and in the case of a basement, or semi-basement, they may require adequate sub-soil drains to be provided under the floor to drain and therefore remove any water that accumulates.

Interestingly, the Regulations now define the word “adequate” in this context:

a) in the opinion of any local authority

b) in relation to any document issued by the council, in the opinion of the council

So if you’re not sure of anything that relates to floors and flooring, approach your local authority for guidance. They are obliged to help you.

Application of the National Building Regulations as they Apply to Floors

In addition to a number of SANS that relate to building materials including boards, timber, concrete and fire testing of materials, the SANS states that Parts A (general principles), B (structural design), H (foundations), T (fire protection) and V (space heating) of SANS 10400 must also be taken into account when constructing floors.

The Application of the Regulations relate to:

  1. floors in wet areas as specified in the Act (that must be water resistant)
  2. suspended timber floors that are not exposed to the elements
  3. floors and slabs supported on the ground
  4. all timber used for building

There are some useful drawings that show how suspended timber floors should be built.

Part J suspended timber floors Floors

Bearing details for suspended timber floors on ground level

Part J suspended floors2 Floors

A competent person (civil engineering) shall design and inspect fills where the maximum height of fill beneath floors, measured at any point, exceeds 400 mm.

There are also specifications for maximum spans of floor joists:

  1. for those made with sawn SA pine for single- and double-storey houses
  2. for those made with laminated SA pine, Grade 5 or higher, also for single- and double-storey houses
Part J sawn SA pine Floors

Sawn SA pine

Part J laminated pine Floors

Laminated SA pine

Additional floor specifications relate to:

  • Flooring boards that must comply with SANS 629 and amongst other things should have a face-side width of at least 50 mm and not more than 140 mm, and tongued on one edge and grooved on the other, with square-sqwn or end-matched ends; and have tongues and grooves that produce a tight-sliding fit, and a flush joint on the face-side of the boards.
  • Strip flooring that amongst other things should have a width between 35 mm and 90 mm and a nominal length  of at least 460 mm (and tongues and grooves as above).
  • Particle board that should comply with SANS 50312 and SANS 1931.
  • Composite and plywood that should comply with SANS 929.

Additional guidelines relating to suspended wooden floors relate to the clearance between the joints and ground; ventilation; metal masonry anchors to be used and so on.

There are also a number of guidelines given for floors that are supported on ground or filling, but it is also stated that this type of floor should be designed and constructed in accordance with the requirements of SANS 10109-1 under the direction of a competent person (civil engineering) unless the building is to be used for storage or industrial purposes, in which case different guidelines are given.

This section also gives guidelines for underfloor membranes and filling beneath floors. Apart from anything else, a competent person (civil engineering) “shall design and inspect fills where the maximum height of fill beneath floors, measured at any point, exceeds 400 mm”.

So even if you go the DIY route, you’re going to need professional assistance.

 

  46 Responses to “Floors”

Comments (46)
  1. I want to buuld a 2nd storey … not sue if I should go wood or concrete…. what is best …. and can I build the 2nd floor with wood what would be the consequence in s.africa

    • Hi Patrick, If you want to build a second storey on a single story house then the first thing you will have to find out is how strong your foundations are and if they can take the weight of a second storey. Timber is a much lighter material and many houses have a second storey built with timber. The timber materials have to be specified by a “competent person” and approved by council.

  2. Hi there.

    I purchased a brand new flat from a develloper. After 14 months the tiles started coming loose and the grout falling out. The developer states that he has a 6 month warranty and after this time takes no responsibilities for defects. Is there some sort of law i can use to make him fix the tiles without me having to pay for the damage?

    • This is clearly a case of shoddy workmanship, however I don’t there is much that you can do except name and shame the developer – e.g. on Hellopeter.

  3. Subject:
    Concrete Floor Alignment
    Message:
    Hi
    I have just purchased a brand new two bedroom apartment and a garage,I paid cash for the Garage R55000. The garage was handed over as Voetstoets ,the flooring is concrete : rough raw finish , not skimmed straight and smooth as i expected to be.Hills and valleys on the floor
    Is there any regulations regarding my complaint.

    • Rajen it depends what your contract states. If it was to be skimmed or screened so that it was smooth this should have been specified. However if it is really sub-standard then you might have recourse via the Consumer Protection Act.

  4. Could you please advise me on the legal requirement for a wooden floor in a double story dwelling. There are two separate families living on either level.

    • Christine the floor would need to be constructed as shown on this page for suspended wooden floors. I am assuming that the fact that two families live in the dwelling is a factor – probably due to noise. This is not covered by the National Building Regulations.

  5. Hi,
    Please could you advise what the regulation is with regards to having an allowance between the internal and external floor levels. I’ve been told it needs to be 150mm, but this seems a bit excessive.
    I have been told my 30mm height is not up to building regulations.
    Thanks
    Dean

    • Hi Dean, the regulations do say the the minimum height between the average surrounding ground level and the top of the internal floor slab is 150mm. Normally you would not have a 150mm step down through a doorway. There should be a landing or patio that leads out through the door then a step or steps down.

  6. hi there
    What is the requirements to build a woodern floor the maxium distance between beams
    thank you

    • Gareth all the information given in the NBR relating to suspended wooden floors – including spacing of joists (which are the beams) – is in the article on this page.

  7. Hi,
    We have a floor (first floor) of rib and block, the builder has placed a concrete stairway from ground floor going 90 degrees to top floor. The height from step to ceiling on the third step is only 180 cm, therefor will not pass building regulation. My question is that when I cut a piece of the upper floor away, can I then use square steel tubing to support the above floor, and if so can I fix it from the third step to the ceiling (most likely place to put it), and lastly what is the thickness of steel that I must use?
    Thanks in anticipation.
    Regards
    Lewis

    • Hi Lewis,
      This sounds too complicated and risky to ask and to answer in a post such as this. I suggest that you contact an engineer or another “competent person” to give you on site advice as this sort of fix needs to be done wtih the safety of all users in mind.

 Leave a Reply

(required)

(required but will remain confidential and not be published)